TRWinProg is a Windows PC program for programming of TR devices (if not programmed by bus / industrial ethernet directly). This means that all TR product lines such as rotary encoders, linear encoders, laser measuring devices, transformation measuring systems, displays with interfaces like Analog, SSI, ISI etc. can be programmed with one software.
TRWinProg compatible devices are marked with the label on the left.

System requirements:

• 80-486 platform or higher
• approx. 40 MB hard disk space
• 32 MB RAM
• CD-ROM drive
• additional free COM interface or USB interface
• Windows 95®/98®/Me® or
• Windows NT 4® / 2000® / XP® / Windows 7® / Windows 8® / Windows 10®

EPROG W32 is a PC program for serial programming of position measuring devices under Windows operating systems:

• Windows 95®/98®/ME®
• Windows NT4®/2000®/XP®

Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m.

Programming interface / software EPROG is no more supported for new devices. This information is only for documentation of older, already installed devices (see TR-V-PCE-DGB-0023)

EPROG is a PC program for serial programming of position measuring devices. An IBM-compatible PC is required. The processor must be at least a 10 MHz 8088 processor or a 6 MHz 8086 processor and the operating system must be at least MS-DOS 3.0. The program also runs in the DOS box of Windows 3.1 or higher versions, then however at least a 486DX2/66 processor must be used.

Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m.

Programming interface / software EPROG is no more supported for new devices. This information is only for documentation of older, already installed devices (see TR-V-PCE-DGB-0023)

PC100 is a PC program for serial programming of position measuring devices under MS-DOS operating systems, version 3.1. or higher up to Windows® 98.

Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m.

PCPNT is a PC program for serial programming of PNT-compatible devices under MS-DOS operating systems, version 3.1. or higher up to Windows® 98.

Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m.

LLB Utility is a PC program for programming of LLB laser measuring devices under Windows® operating systems via serial interface. Supported are the COM ports 1-9. The configuration of the device can be made in a simple manner, without knowing the individual ASCII based commands. As an alternative, any other terminal program can be used.

Software to calculate the check sum of the iParameters (F_iPar_CRC).

TR SNCT Device Applet used for configuration of CIP Safety Targets according to the download process "SNCT-to-Target". Allows the configuration of the secondary interface. Allows the evaluation of the device diagnostics.

With this program the PROFIsafe destination address “F_Dest_Add” can be set (AD_88)

LT-Prog is a Windows PC program for programming of transformation measuring systems.
Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m.

System requirements:

• 80-486 platform or higher
• approx. 5 MB hard disk space
• 16 MB RAM
• CD-ROM drive
• additional free COM interface
• Windows 95®/98®/Me® or
• Windows NT 4® / 2000® / XP®

BE 901 driver software for USB connection BE 901

BE-90 Configuration Tool is a Windows PC program for programming of barcode positioning systems:

BE-90 SSI, synchronous serial interface

Operating manual

Program